OPIS PRODUKTU
Najnowsza, przełomowa technologia izolacji dachów płaskich metodą „2 w 1” (zintegrowane funkcje hydro- i termoizolacji) wykorzystuje płyty ze sztywnej pianki PU pokryte fabrycznie warstwą hydroizolacji ze specjalizowanej membrany dachowej. Maksymalnie uproszczony układ jednowarstwowy pozwala na oszczędności czasu montażu o ok. 50% w porównaniu do systemów wielowarstwowych. Fabryczne zespolenie warstwy hydroizolacji z izolacją termiczną zapobiega powstawaniu pustych przestrzeni, co znacznie poprawia wydajność i trwałość układu. Mocowanie płyt do podłoża betonowego lub stalowego (blacha trapezowa) przy pomocy systemowych układów teleskopowych. Styki płyt zgrzewane fałdami zakładu membrany dachowej. Dostępny pełen zestaw akcesoriów montażowych.
CECHY SZCZEGÓLNE
Bardzo dobre parametry termoizolacyjne. Duży zakres grubości (80, 100, 125, 140, 175mm). Jednowarstwowy układ hydroizolacji (membrana dachowa 1,2 mm jako okładzina zewnętrzna płyt). Odporność na ściskanie 120 kPa (przy 10% odkształceniu). Klasa reakcji na ogień B-s2, d0. Klasyfikacja odporności ogniowej REI 20. Odporność na ogień zewnętrzny BROOF (t1). Płyty standardowo dostępne w formatkach 1000 × 2400 mm (szer. × dł.). Na indywidualne zamówienie możliwość zoptymalizowania długości płyt do wymiarów dachu (zmniejszenie ilości połączeń poprzecznych). Doskonała odporność na zmiany temperatur i promieniowanie UV. Zgodność z normą PN-EN 13165:2010.
PolTherma SOFT panels are insulating panels made of rigid foam PU. The use of PolTherma SOFT panels offers a number of tangible benefits both during installation and during operation of the building.
Available cladding:
- LAMINATE/COMPOSITE— laminate on one side/ multilayer cladding: paper, PE film, aluminum foil on the other side
- COMPOSITE — both sides multilayer cladding: paper, PE film, aluminum foil
Key features of insulating panels PolTherma SOFT:
- Very good thermal insulation – the best of the materials currently used in the construction industry
- the lowest value of thermal conductivity d = 0.022 [W/m2 * K] *
- almost twice lower value of the insulation layer in relation to other known insulating materials, with the same coefficient U
- High thermal stability during the lifetime due to the closed cell structure
- Extremely low hygroscopicity (lower than 3%) for core
- High chemical resistance of the core to organic solvents
- Low weight – minimal load on the structure
- Resistance to fungi and microorganisms
- No core degradation in lifetime
- Simple and safe installation
- Dimensional stability
- Conformity with UE standards CE wg EN 13165:2001
* Declared value at +10 ° C
Main advantages of PolTherma SOFT panels:
Using the POlTHERMA SOFT as an effective thermal insulation of the building allows the rapid increase temperature in heated rooms. At the same time prevents cooling down and helps to keep the constant temperature. POLTHERMA SOFT is an excellent thermal insulation in winter and summer.
Thanks to the PU core, PolTherma Soft is very resistant for the mechanical deformations and compressions. These features are necessary to make the efficient thermoinsulation of flat roof and prevents problems with maintenance in the future.
The assembly of insulation boards PolTherma Soft is very easy, thanks to their low weight and simple montage, without dusting. The overlapped joint is an additional advantage. Boards are available in packages or on order.
An important parameter determining the thermal insulation of material is its low water absorption. The POLTHERMA SOFT is made of the best insulation core of PU. Thanks to its closed cells characterized by a very high resistance to penetration of moisture and air infiltration
Roof panels enable an easy and quick assembly for various types of structures with the use of specialized screws.
Specifically designed and profiled tongue and groove joints of roof sandwich panels guarantee a very good tightness and make the whole structure fireproof.
ThermaDeck PRO is an example of roof sandwich panels with EPS (expanded polystyrene) core. In our product you have a choice of assembling method: panels could be secured to supporting construction by a screw that comes throughout the panel (visible joint) or with a specialized WLOZAMOT jumper and a screw (invisible joint).
ThermaDeck PRO panels are recommended for roofs with a slope of at least 4°(7%) with one panel up to 7 m length and at least 6° (10%) for panels joined on length, with sky-lights, chimneys etc .
Roof sandwich panel ThermaDeck PRO is available in profilings:
- Grooved – ThermaDeck PRO T
Available option:
- FLEXI – panel with internal flexible facing instead of metal one
PoldDeck is a roof sandwich panel with a core of rigid PU foam, the inner lining of laminate, fixed to the supporting structure by a fastener through the entire thickness of the panel.
External cladding is metal, as in the standard TD roof panels. PolDeck MD is a panel to be used mainly in livestock buildings, where there is great concentration of ammonia or the need for warming the existing roof covering.
PolDeck MD panel is suitable for use in horticulture, storage rooms, warehouses, barns, poultry houses, in buildings with pitched roof, at least 4 ° (7%) for continuous panels and 6 ° (10%) for panels joined alongside, with skylights, etc. Laminate / jut cladding can be cleaned with Karcher.
Advantages of roof sandwich panels PolDeck MD:
- Low water absorption – less than 1%
- Resistant to chemicals and biological agents:
- Acids / very good
- Alcohol / very good
- Base / good
- Solvents / good
- Ammonia / very good
- Molds / very good
- The surface of the laminate can be cleaned with water high pressure cleaners
- Operating temperature -40°C do 110°C
- Fire resistance: no dripping M class / French
PolDeck TD Europanels is a Trapezoidal roof panel with polyurethane foam. Fastening method it throughout to supporting beams by a self-drilling screw. PolDeck TD (Trapezoidal Deck) is an example of universal roof panel being a good choice for variety of buildings. Required slope is at least 4°(7%) for single panels and 6° (10%) for panels with skylights, overlapped etc.
Europanels offers sandwich panels with pre-cut of the internal facing – overlapping L and R for a gutter (Z) joining on length etc. 50-300mm
Sandwich panels are ready to use composites. It is extremely important to make a proper measurement of the length of panels to be installed, to avoid ordering too long (unnecessary waste) or too short ones (which sometimes makes it impossible to assemble at all). Length of the plate should be specified in the building design. Panels shall also be measured on the basis of the finished supporting structure as this could differ from plan. Customer / buyer are responsible for correctness of the lengths specification (professionally called “cutting list”).
Roof supporting structure, designed for mounting panels can be made out of steel, wood or reinforced concrete. For each of these types of structures there are different, specialized fastening solutions in EuroPanels offer.
Be sure to maintain proper spacing of the purlins and check their parameters: profile type, length and width etc. according to the construction project. The supporting structure is the load bearing for the panels, which provide loads (snow, wind and rain).
Due to the side effects of strong sunlight, UV and extreme temperatures which heat up the surface of the roof, we recommend that roof panels shall be made in the white (for example RAL 9010). Also important is to use the expansion joints and joining panels of length with overlapping in order to “shorten” total length of a single panel. Thus allows a proper “work” on the panels’ structure and compensation of changes in the skins length affected by extensive heat.
Wall sandwich panels with mineral wool are made of two steel sheet metallic facings and a construction-insulation core layer. The core layer is made of mineral wool. The panels can be fixed to different kinds of structures throughout the whole panel with the specialized screws. Specifically designed and profiled tongue and groove joints guarantee a very good tightness and make the whole structure fireproof
Wall sandwich panels MWS are available in profilings:
- micro-wave V - MWS V panel
- micro-trapezodial T - MWS T panel
Wall sandwich panels with mineral wool are made of two steel sheet metallic facings and a construction-insulation core layer. The core layer is made of mineral wool. The panels can be fixed to different kinds of structures throughout the whole panel with the specialized screws. Specifically designed and profiled tongue and groove joints guarantee a very good tightness and make the whole structure fireproof
Wall sandwich panels MWS are available in profilings:
- micro-wave - MWS V panel
- micro-trapezodial – MWS T panel
ThermaStyle PRO is a wall sandwich panel with EPS (expanded polystyrene) core. In the EuroPanels solution, there is a choice of fastening method: with invisible screw (by a special element) or throughout directly to supporting construction (visible head of a screw). In first solution (our patent), even in the entry-level sandwich panel product it is possible to achieve a smooth design of a wall surface. The ThermaStyle PRO panel is popular as cheap, easy and fast solution for walls including partitions in a variety of buildings.
Wall sandwich panel ThermaStyle PRO is available in profilings:
- Linear – ThermStyle PRO L
- Grooved – ThermaStyle PRO T
- Micro – ThermaStyle PRO M
PolTherma PS is a wall sandwich panel with a rigid PU core, assembled to supporting construction in an invisible way (hidden joint). PolTherma PS series takes advantage specially for the expansions – in already existing buildings with standard profiling, new part of wall can also look similar to already existing. With smart solution of hidden joint, design of a new wall is modern and smooth. Due to a special profiling on the joining edges, screws and required special washer are hidden by the next panel’s nose. Thus, building elevation is free from any visible fastening points.
Wall sandwich panel PolTherma PS is available in profile options:
- Micro - PolTherma PS M
- Linear – PolTherma PS L
PolTherma PS is available in special option:
- FLEXI – panel with internal flexible facing instead of metal one. This kind of product is the best for thermo-modernization (building insulation) as well as for renovation (refresh elevation).
PolTherma CS is a specialized wall panel with polyurethane core. It is dedicated to cold storage applications. Fixing is visible (screw comes throughout the panel). Additionally to cold storage dedication, the CS Series is suitable to all of the applications where thermal properties of wall is most important.
The PolTherma CS is recommended also to agriculture buildings specialized as storage of fruits and vegetables.
Better resistance to thermal deformation for the new profiling:
- MicroCoffer MK 550 – PolTherma CS MK550
Also available in standard profiling:
- Linear – PolTherma CS L
- Micro – PolTherma CS M
- Grooved – PolTherma CS R
Recommendations: application of the butyl sealant on the panel joint (over the entire length of panel) is obligatory on ceilings. For walls it is an option.
PolTherma TS is a standard wall panel with a core of PU rigid foam. Fastening to supporting construction is realized by a screw that comes throughout the whole panel (visible joint). Main features of the TS panels are: high durability, easy fixing, wide modular width (1130 mm). The TS Series is equipped with side gasket that improves tight of joint (being a seal).
The PolTherma TS is an example of standard product featured in nowadays technology. PolTherma TS is a best choice for agriculture buildings.
Better resistance to thermal deformation for the new profiling:
- MicroCoffer MK 550 – PolTherma TS MK550
Also available in standard profiling:
- Linear – PolTherma TS L
- Micro – PolTherma TS M
- Grooved – PolTherma TS R
Sandwich panels PolTherma TS could be installed both in horizontal and vertical way to steel, wood and reinforced concrete structures.
PolTherma DS is a wall sandwich panel with a rigid PU core, assembled to supporting construction in an invisible way (hidden joint). Due to a special profiling on the joining edges, screws and required special washer are hidden by the next panel’s nose. Thus, building elevation is free from any visible fastening points. Absolutely unique profiling design of the PolDherma DS Series are absolutely best looking wall panels available.
Wall sandwich panel PolTherma DS is available in profile options:
- Slanting – PolTherma DS S
- MicroCoffer 500 – PolTherma MK500
PolTherma DS is available in special option:
- FLEXI – panel with internal flexible facing instead of metal one. This kind of product is the best for thermo-modernization (building insulation) as well as for renovation (refresh elevation).
PolTherma DS is an example of the most modern technology currently available in world’s sandwich panel production, not only in the field of molding PU polyurethane core, but also in industrial design, which is associated with advanced profiling processes of the facing.
The PolTherma DS Series panels were awarded with Gold Medals for Best Product on International Construction Fair BUDMA Poznan and Agriculture Fair AGROTECH Kielce, Poland.
English
